Top 10 typical forklift crashes ， forklift procedure must focus on these issues ！.

Top 10 typical forklift crashes ， forklift procedure must focus on these issues ！.

Blog Article

Don't take too lightly the forklift at work. If the operation is not good, there will be severe crashes in mins, and there are numerous crashes entailing forklifts.

Case 1: The forklift freight obstructed the driver's sight, and the person ahead can not be located, causing a moving crash.
Situation 2: In order to preserve the balance of the forklift when lifting heavy goods, the employees utilized their body weight as the weight, which virtually created casualties.
Situation 3: The width of the forklift cargo exceeds the allowed size of the path and hangs on the roadside shelf, which almost creates an crash.
Situation 4: Forklift is speeding and rolls over throughout a turn.
Instance 5: The forklift motorist did not discover the pedestrian, and the pedestrian did not discover the forklift.
Case 6: The forklift raises the workers illegally, the forklift driver does not put on the seat belt, the forklift lifter falls and the vehicle driver is squashed when the forklift rolls over.
Case 7: The forklift vehicle driver did not use a seat belt and dropped from the automobile when it rolled over and was squashed.
Forklift operation should pay attention to these issues ：.

Start.
1. Prior to starting, observe the environments, and after verifying that there are no obstacles that prevent the security of driving, honk the horn initially and then begin.
2. For cars with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) gauge must be risk-free before beginning.
3. When the forklift starts with a tons, the vehicle driver must initially verify that the lots is steady and reliable.
4. The begin must be sluggish and steady.

Driving.
1. When driving, the height in between the bottom end of the fork and the ground ought to be maintained 300mm-400mm, and the mast must be slanted backward. .
2. Do not raise the fork too high when driving. When getting in and leaving the job site or while driving, take care that there will be no challenges overhead. When the load is traveling, the fork has to not be raised too expensive, which will certainly affect the stability of the forklift. .
3. After discharging, the fork needs to be lowered to the typical driving placement prior to driving. .
4. When transforming, if there are pedestrians or cars close by, the driving signal needs to be released first. High-speed sharp turns are forbidden. High-speed doglegs will cause the automobile to shed side security and tip over. .
5. When the forklift is downhill, it is strictly forbidden to shut off the flame and slide, and it is prohibited to brake instantly while driving with lots unless there are unique situations.
6. When the forklift is running, it needs to follow the website traffic rules in the manufacturing facility and must keep a certain safety distance from the car in front. .
7. When the forklift is running, the load should be in the lowest position that does not hinder the driving, and the gantry ought to be correctly tilted back. The tons shall not be raised except when stacking or loading. .
8. The height of the load must not block the driver's view. In unique conditions, when the thing influences the forward vision, drive at a reduced rate when turning around.
9. It is prohibited to turn on the ramp, nor to drive throughout the ramp. .
10. The secure driving rate of the forklift in the manufacturing facility area is 5 km/h, and it should drive safely at a reduced rate when going into the production workshop location. .
11. When the forklift is raised, lifted or driven, it is forbidden for personnel to depend on the fork to hold things and play a balancing role. .
12. If troubles are located, they will be repaired and reported in a timely fashion, and they will never run with health problems or conceal them.

loading and dumping.
1. When fork-loading products, the distance in between the two forks should be changed as needed to make the lots of the two forks balanced and not manipulated, and one side of the item should protest the rack. .
2. It is restricted to deal with a solitary fork or utilize a fork top or pull. In unique situations, safety and security warning signs must be established to remind bordering pedestrians. .
3. In the process of loading and discharging items, the forklift needs to be braked with the brake. .
4. The rate of the vehicle must be slow and consistent. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled things and harm individuals. .
5. When using a fork to fork the goods, the fork needs to be as deep as possible under the lots, and it should be kept in mind that the fork pointer ought to not touch various other goods or items. The lots should be supported with marginal back tilt of the gantry to ensure that the tons does not glide backwards. The mast can be slanted forward somewhat when the tons is decreased to allow for simple positioning of the load and extraction of the forks. .
6. It is prohibited to fork items at broadband and collide with difficult things with the fork head. .
7. When the forklift is functioning, it is forbidden for people to stand around the fork, so regarding stay clear of the collapse of the goods and injure people. .
8. Overwhelming is forbidden, and it is banned to use forks to lift workers to participate in high-altitude procedures to stay clear of high-altitude dropping accidents. .
9. It is not enabled to utilize the brake inertia to slide, place, round or roll things. .
10. It is not permitted to use forks to pick, turn pallet unload.

Leaving .
1. It is prohibited to leave the forklift when the things on the fork are in the air. Before leaving the forklift, you must unload the goods or lower the fork frame.
2. Pull the parking brake deal with to dead or depress the parking brake switch.
3. The engine is turned off and the power is cut off. (Except for special circumstances, such as the driver does not leave the vehicle's view and does not go beyond 1 min).
4. Get rid of the secret. .

Forklift Operation Precautions.
1. Before and after the forklift operation, the appearance should be examined, and gas, Stand-on Electric Pallet Stacker lubing oil and cooling water ought to be added.
2. Check the safety and security efficiency of starting, running and braking.
3. Check whether the lights and horn signals are full and reliable.
4. During the operation of the forklift, examine whether the stress and temperature are normal.
5. After the forklift is running, the external leak must likewise be checked and the seals need to be changed in time.

Forklift Safety Operation Specifications.
1. You should check prior to leaving the cars and truck;.
2. When you come across someone before you throughout driving, you ought to send out a signal at a distance of 5 m;.
3. The driving rate in the factory does not go beyond 5 km/h;.
4. When driving, the low point of the freight must be 0.3 m ~ 0.4 m above the ground;.
5. The transforming ought to not be too sharp to stop the tendency of " cost-free turning";.
6. Adding and down the incline should be slow-moving and uniform, and no activating the slope is permitted.
7. Do not drive across the slope. When the gradient is more than 10%, the automobile should be driven backwards when going downhill;.
8. When the forklift workers carry the goods and progress, if they encounter big or heavy products and most likely to the chauffeur's view, they ought to take the turning around exercise
.
The "Eight Prohibitions" must be adhered to in the operation.
1. Solitary fork procedure is not allowed.
2. It is not enabled to raise the goods for far away driving.
3. It is not permitted to pick up the goods by handing over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and other unsafe chemicals with forks.
5. It is not allowed to utilize inertia pressure to grab the goods.
6. It is not allowed to utilize stopping pressure to exile round or easy-to-roll items.
7. It is not enabled to bring individuals to work on the pallet or fork, and it is strictly restricted Stand-on Electric Pallet Stacker to stand under the fork after the fork is elevated.
8. Do not drive laterally on slopes
.
Car park is not permitted under the following conditions.
1. Curves, slim roadways, railway crossings;.
2. Sections with a longitudinal slope higher than 5%.
3. When there is an challenge on one side of the roadway, the contrary side of the area with the very same length as the obstacle ought to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844